C8 tire pressure

W

WLGJ

High RPM Poster
You're a Donor King of the Post You're Liked Completionist Award You're a Regular You're Celebrated C8
Messages
1,699
Reaction score
964
VetteCoins
34,456
My tire pressure gauge says relearn!? Do I need one of those gadgets to reset my tpms or can it be done directly from the C8?
 
Murray20c8 said:
It's done automatically. I think you just have to drive it.
Click to expand...
I did a few Ks yesterday but did not reset. Rain here today, so next time will roll more and see.
Thanks
 
Hope it does just need a reset.
Does the TPMS flash and then come on steady? That indicates an error with the system.

TPMS Sensor Matching Process
— Auto Learn Function Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the tires or replacing one or more of the TPMS sensors. When a tire is installed, the vehicle must be stationary for about 20 minutes before the system recalculates. The following relearn process takes up to 10 minutes, driving at a minimum speed of 20 km/h (12 mph). A dash (-) or pressure value will display in the DIC. See Driver Information Center (DIC) 0 108. A warning message displays in the DIC if a problem occurs during the relearn process.
 
Murray20c8 said:
Hope it does just need a reset.
Does the TPMS flash and then come on steady? That indicates an error with the system.

TPMS Sensor Matching Process
— Auto Learn Function Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the tires or replacing one or more of the TPMS sensors. When a tire is installed, the vehicle must be stationary for about 20 minutes before the system recalculates. The following relearn process takes up to 10 minutes, driving at a minimum speed of 20 km/h (12 mph). A dash (-) or pressure value will display in the DIC. See Driver Information Center (DIC) 0 108. A warning message displays in the DIC if a problem occurs during the relearn process.
Click to expand...
It says relearn , so I did what was in the book/video, you hold the knob until the horn beeps and that should do it. I am going to try something else. I think I might have to do a reset for each tires until the horn beeps!? If this does not work I will mention it when I get my oil change because I need to go and have the car in for the 2 recalls.
 
Pge 84 2024 OM
"
Info Titles Selection
Use the thumbwheel to select the items to
be displayed in the display areas. See "Info
Tiles" previously in this section.
If the maximum amount of info tiles has
been selected, all deselected info tiles
appear in an disabled state. If maximum
amount of info tiles is not selected, all info
tiles appear in an normal state and can be
selected. In the default layout, the info tiles
will be inserted from top to bottom. In the
enhanced layout, the info tiles will be
inserted from top left to top right to bottom
left to bottom right. Info tiles that are
already occupied will be skipped.
Tachometer
Available in some Drive Modes, press the
thumbwheel while Tachometer is displayed
to enter the Tachometer menu. Choose
Traditional or Numerical by pressing the
thumbwheel while the desired item is
highlighted. A selected mark will be
displayed next to the selected item.
Traditional tachometer shows a linear gauge,
and Numerical tachometer shows shift lights
with numerical RPM.
Units
Press the thumbwheel while Units is
displayed to enter the Units menu. Choose
US or metric units by pressing the
thumbwheel while the desired item is
highlighted. A selected mark will be
displayed next to the selected item.
Tire Pressure <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Use the thumbwheel to select the tire
pressure warning thresholds. Choose Light,
Eco, or Max by pressing the thumbwheel
while the desired item is highlighted.
A selected mark will be displayed next to
the selected item.
If the tire pressure readings need to be
recalibrated at any time, this option initiates
the Tire Pressure Relearn function. The
selection of relearn opens a pop-up when
the thumbwheel is pressed for five seconds."
 
MKC8 said:
Pge 84 2024 OM
"
Info Titles Selection
Use the thumbwheel to select the items to
be displayed in the display areas. See "Info
Tiles" previously in this section.
If the maximum amount of info tiles has
been selected, all deselected info tiles
appear in an disabled state. If maximum
amount of info tiles is not selected, all info
tiles appear in an normal state and can be
selected. In the default layout, the info tiles
will be inserted from top to bottom. In the
enhanced layout, the info tiles will be
inserted from top left to top right to bottom
left to bottom right. Info tiles that are
already occupied will be skipped.
Tachometer
Available in some Drive Modes, press the
thumbwheel while Tachometer is displayed
to enter the Tachometer menu. Choose
Traditional or Numerical by pressing the
thumbwheel while the desired item is
highlighted. A selected mark will be
displayed next to the selected item.
Traditional tachometer shows a linear gauge,
and Numerical tachometer shows shift lights
with numerical RPM.
Units
Press the thumbwheel while Units is
displayed to enter the Units menu. Choose
US or metric units by pressing the
thumbwheel while the desired item is
highlighted. A selected mark will be
displayed next to the selected item.
Tire Pressure <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Use the thumbwheel to select the tire
pressure warning thresholds. Choose Light,
Eco, or Max by pressing the thumbwheel
while the desired item is highlighted.
A selected mark will be displayed next to
the selected item.
If the tire pressure readings need to be
recalibrated at any time, this option initiates
the Tire Pressure Relearn function. The
selection of relearn opens a pop-up when
the thumbwheel is pressed for five seconds."
Click to expand...
I will go back and try it now.
thank you
 
MKC8 said:
Pge 84 2024 OM
"
Info Titles Selection
Use the thumbwheel to select the items to
be displayed in the display areas. See "Info
Tiles" previously in this section.
If the maximum amount of info tiles has
been selected, all deselected info tiles
appear in an disabled state. If maximum
amount of info tiles is not selected, all info
tiles appear in an normal state and can be
selected. In the default layout, the info tiles
will be inserted from top to bottom. In the
enhanced layout, the info tiles will be
inserted from top left to top right to bottom
left to bottom right. Info tiles that are
already occupied will be skipped.
Tachometer
Available in some Drive Modes, press the
thumbwheel while Tachometer is displayed
to enter the Tachometer menu. Choose
Traditional or Numerical by pressing the
thumbwheel while the desired item is
highlighted. A selected mark will be
displayed next to the selected item.
Traditional tachometer shows a linear gauge,
and Numerical tachometer shows shift lights
with numerical RPM.
Units
Press the thumbwheel while Units is
displayed to enter the Units menu. Choose
US or metric units by pressing the
thumbwheel while the desired item is
highlighted. A selected mark will be
displayed next to the selected item.
Tire Pressure <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<
Use the thumbwheel to select the tire
pressure warning thresholds. Choose Light,
Eco, or Max by pressing the thumbwheel
while the desired item is highlighted.
A selected mark will be displayed next to
the selected item.
If the tire pressure readings need to be
recalibrated at any time, this option initiates
the Tire Pressure Relearn function. The
selection of relearn opens a pop-up when
the thumbwheel is pressed for five seconds."
Click to expand...
It did the job, thank you very much. :Woohoo:
 
WLGJ said:
It says relearn , so I did what was in the book/video, you hold the knob until the horn beeps and that should do it. I am going to try something else. I think I might have to do a reset for each tires until the horn beeps!? If this does not work I will mention it when I get my oil change because I need to go and have the car in for the 2 recalls.
Click to expand...
Recalls ?
 
One recall is to see if the daylight lights turn on and stay on. I don't remember the other.
 
WLGJ said:
One recall is to see if the daylight lights turn on and stay on. I don't remember the other.
Click to expand...
Right. That was the one causing the border clearance issue because Transport Canada weren’t happy with the US version of how they worked wasn’t it ?
 
1st Vette said:
Right. That was the one causing the border clearance issue because Transport Canada weren’t happy with the US version of how they worked wasn’t it ?
Click to expand...
You have me there. My lights work fine. I really don't know what the recall is.
 
WLGJ said:
You have me there. My lights work fine. I really don't know what the recall is.
Click to expand...
Had to do with the daytime running lights as you stated. That’s the only one I can remember. Really when you take a look at the recall situation with the C8 they are actually few and far between compared to a lot of other new vehicles. They did a good job designing and building them it seems . Not much to complain about.
 
1st Vette said:
Had to do with the daytime running lights as you stated. That’s the only one I can remember. Really when you take a look at the recall situation with the C8 they are actually few and far between compared to a lot of other new vehicles. They did a good job designing and building them it seems . Not much to complain about.
Click to expand...
This is my first time in a recall with my C8. It must of been a few because my lights always worked well. I guess they recall them all.
 

Similar threads

Users who are viewing this thread

Total: 2 (members: 0, guests: 2)
Back
Top